>> P.429
JCRBHVCRBFVCRB(C)CRBTCRBTFCRBS1N=0.102kgf=0.2248lbs.1mm=0.03937inchTable 10.2 Tolerances and allowable values of outer rings of CRBFVunit: μmKeaRadial run-out of assembledbearing outer ringSeaAssembled bearing outer ringface run-out with racewayP2RP22.5445555557P5 RP5P4RP455566778810 7 8 810101111131315P2Class P6RP610131318182020232325020252535354040454550RP22.5445555557P5 RP5P4RP455566778810 7 8 810101111131315Class P6020252535354040454550RP610131318182020232325DNominal outside diametermm∆DmpSingle plane mean outside dia. deviationClass 0RP6-2 P6P5P4, P2∆CsDeviation ofa single outer ring width-75-75-75-75-75-75-75-75-75-750000000000- 7- 7- 8- 8- 9- 9-10-10-11-110000000000- 9- 9-10-10-11-11-13-13-15-150000000000-11-11-13-13-15-15-18-18-20-200000000000-13-13-15-15-18-18-25-25-30-30000000000050608095120140150165180210608095120140150165180210240OverIncl.HighLowHighLowHighLowHighLowHighLowTable 11 Tolerances of LCRB unit: μmInner ring(1)Outer ring(1)Identification numberLCRB 50LCRB 70∆dmpSingle plane mean bore dia. deviation for d∆BsDeviation of a single inner ring width for bi∆DmpSingle plane mean outside dia. deviation for D∆CsDeviation of a single outer ring width for BoHigh300300Low-300-300High200200Low-200-200High300300Low-300-300High200200Low-200-200Notes(1) or the boundary dimensions indicated by each symbol, see pages J29 to J30.■ClearanceThe radial internal clearances of Crossed Roller Table 12.2 adial internal clearances of CRBT and Bearings are shown in Table 12.1. However, Table 12.2 is CRBTFunit: μmRadial internal clearanceC1Max.151515151515Min.000000dNominal bore diameter of bearingmm101520304050Table 12.3 Radial internal clearances of CRBSdNominal bore diametermm 50 60 70 80 90100 110 120 130 140 150 160 170 180 190 200unit: μmRadial internal clearanceT1C1NormalMin.- 8- 8- 8- 8- 8- 8- 8- 8- 8- 8- 8-10 -10 -10 -10 -10 Max.0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0Min.0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0Max.15151515151515151515152020202020Min.30303041414141515151515151616161Max.56565666666666767676767676868686J10applicable to Super Slim Type Crossed Roller Bearings and Mounting Holed Type Super Slim Crossed Roller Bearings, Table 12.3 is applicable to Slim Type Crossed Roller Bearings, and Table 12.4 is applicable to Mounting Holed Type High Rigidity Crossed Roller Bearings V. For the radial internal clearances for Lightweight Crossed Roller Bearings, see pages J29 to J30.Table 12.1 Radial internal clearancesunit: μmdNominal bore diametermmRadial internal clearanceT1C1C2Over- 30 40 50 65 80100 120 140 160 200 250 315 400 500 630 710 Incl. 30 40 50 65 80100 120 140 160 200 250 315 400 500 630 710 800Min.-10 -10 -10 -10 -10 -10 -15 -15 -15 -15 -20 -20 -25 -30 -30 -30 -40Max.0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Min.0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Max.1010101015151520202025253040506070Min.1010101015151520202025253040506070Max. 20 20 25 25 30 35 35 45 50 50 60 60 70 85100 120 140Remark Not applicable to Super Slim Type Crossed Roller Bearings, Mounting Holed Type Super Slim Crossed Roller Bearings, Slim Type Crossed Roller Bearings, Mounting Holed Type High Rigidity Crossed Roller Bearings V, or Lightweight Type Crossed Roller Bearings.
| < 
| 
> | 
>>
