>> P.430
交叉滚子轴承表8超薄型及超薄型附带安装孔交叉滚子轴承的容许公差及容许值d公称轴承内径mm101520304050∆dmp∆Dmp平面内平均内径的平面内平均外径的尺寸公差尺寸公差∆Bs及∆Cs实测内圈宽度及外圈宽度的尺寸公差上限下限上限下限上限000000-8(-8)-8-10(-10)-10(-10)-12(-12)-12000000-9(-11)-9-11(-13)-11(-13)-13(-13)-13000000下限-75-75-75-75-75-75备注()内的数值表示附带安装孔的超薄型交叉滚子轴承的值。表9薄型交叉滚子轴承的容许公差及容许值d公称轴承内径∆dmp∆Dmp∆Bs及∆Cs平面内平均内径的平面内平均外径的实测内圈宽度及外圈宽度的尺寸公差尺寸公差尺寸公差mm5060708090100110120130140150160170180190200上限0000000000000000下限-15-15-15-20-20-20-20-25-25-25-25-25-25-30-30-30上限0000000000000000下限-13-13-15-15-15-15-20-20-25-25-25-25-30-30-30-30上限0000000000000000下限-127-127-127-127-127-127-127-127-127-127-127-127-127-127-127-127Kia及Sia内圈的径向跳动及轴向跳动最大10(13)1013(13)13(15)15(15)15Kia及Sia内圈的径向跳动及轴向跳动最大单位μmKea及Sea外圈的的径向跳动及轴向跳动最大15(20)1520(20)20(25)25(25)25单位μmKea及Sea外圈的的径向跳动及轴向跳动最大1313151515152020252525252530303013131515151520202525252525303030表10.1附带安装孔的高刚性交叉滚子轴承V内圈的容许公差及容许值d∆dmp公称轴承内径平面内平均内径的尺寸公差∆Bs实测内圈宽度的尺寸公差0级RP6-2下限上限P6P5P4、P2上限下限上限下限上限下限上限下限Kia径向跳动单位μmSia轴向跳动0级P6RP6P5RP5最大P4RP4P2RP20级P6RP6P4RP4P2RP2P5RP5最大2.52.52.52.52.52.52.52.534444556455556682.52.52.52.52.52.52.52.513151520202525308101010101313183444455645555668-75-75-75-75-75-75-75-75131515202025253081010101013131800000000-5-5-6-6-7-7-8-800000000-6-6-8-8-9-9-10-1000000000-8-8-10-10-12-12-15-1500000000-10-10-12-12-15-15-20-2000000000mm超过以下203035506580100120─203035506580100430
| < 
| 
> | 
>>
